|
Home Grandfather ClocksWall Clocks Mantel Clocks Antique Clocks Atomic ClocksClock Owners Manuals
Clock BrandsClock RepairClock Service LocationsClock Parts Clock NewsClock Reviews
IMPORTANT INFORMATION The product information label lists the Grandfather Clock model number and serial number. The Grandfather Clock model number and serial number are essential for obtaining parts or service. The product information label may be located in several locations: outside the shipping carton, back of door, back of the Grandfather Clock, top of the Grandfather Clock, inside the top back corner of the Grandfather Clock, or inside the Grandfather Clock above the back of the dial. For easy reference in the future, take a moment to record these numbers. BASIC OPERATION OF A GRANDFATHER CLOCK At the heart of every Grandfather Clock is the movement. The movement controls the hour strike, time keeping, and chime. The pendulum and weights are critical components to operation of the Grandfather Clock movement. The pendulum provides the ability to regulate and adjust the time keeping. As described within these instructions, adjustments to the pendulum to achieve accurate time keeping is easily accomplished. The three weights provide power to the hour strike (left weight), time (center weight), and chime melody (right weight). Without these weights, the Grandfather Clock would not operate. Each weight is different and must be properly hung from the movement (left, center, right) to ensure proper operation. Weights are hung from the movement by a cable or chain. The weights must be raised at least every 7 days or the Grandfather Clock will stop. Raising cable driven weights is accomplished through use of a crank. Raising chain driven weights is accomplished by pulling down on the loose end of the chain. The strike and chime sounds are made by a series of hammers hitting various length rods. Each rod makes a different sound when hit by a hammer. Specific chime melodies are achieved by controlling the sequence that each hammer hits a corresponding rod. TABLE OF CONTENTS Grandfather CLOCKS WITH CABLE MOVEMENTS Setting Up Your Grandfather Clock . . . . . . . . . . . . . . . . . . . . 1 Leveling Your Grandfather Clock. . . . . . . . . . . . . . . . . . . . . . .2 Hanging Pendulum . . . . . . . . . . . . . . . . . . . . . . .3 Hanging Weights . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting Moon Dial . . . . . . . . . . . . . . . . . . . . . . . .5 Setting Time . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Starting Grandfather Clock . . . . . . . . . . . . . . . . . . . . . . . . . .7 GENERAL INFORMATION Naruto shippuden legends akatsuki rising psp download. Product Information Label . . . . . . . . . . . . . . . . . . . 8 Moving Your Grandfather Clock . . . . . . . . . . . . . . . . . . . . . . . . 9 Installing / Removing Top Side Panel . . . . . . . . . . . .10 Raising Weights . . . . . . . . . . . . . . . . . . . . . . . . . .11 Regulating Timekeeping . . . . . . . . . . . . . . . . . . . . .12 Automatic Night-Time Silencing Option . . . . . . . . . . .13 Chime Selection . . . . . . . . . . . . . . . . . . . . . . . . . .14 TROUBLE SHOOTING Difficulty Turning The Moon Dial . . . . . . . . . . . . . . . 15 Grandfather Clock Does Not Chime At Proper Time . . . . . . . . . . . .16 Grandfather Clock Does Not Strike The Correct Hour . . . . . . . . . . 17 Ati radeon 9550 driver for mac. Grandfather Clock Will Not Chime or Strike . . . . . . . . . . . . . . . . . 18 Chimes Have The Incorrect Tone. . . . . . . . . . . . . . . .19 Weights Do Not Drop At The Same Level. . . . . . . . . . .20
______________________________________________________________
______________________________________________________________
______________________________________________________________
______________________________________________________________
|
6. SETTING TIME (moving the hands)To set the time, move ONLY THE MINUTE HAND counter Clockwise (backwards) until hour and minute hand are at the correct time. (See figure 6). DO NOT MOVE THE HOUR HAND WHEN SETTING THE TIME. The hour hand will move automatically when the minute hand is moved. By moving the minute hand counter Clockwise it is not necessary to wait for the Grandfather Clock to chime as the minute hand passes each quarter hour. (See figure 6). The movement has a self correcting feature which synchronizes the chimes with the time. If after setting the Grandfather Clock on time, it does not chime properly, permit it to operate 2 hours to correct itself. Never move the hand while the clock is chiming or striking. CAUTION ON MOVEMENTS WITH AUTOMATIC CHIME SEQUENCING: The chime selection lever should not be in the 'Auto' position when moving the hands. Moving the hands in either the Clockwise or counter Clockwise direction while the automatic chime sequencing is in operation could damage the chime mechanism. |
______________________________________________________________
7. STARTING THE GRANDFATHER CLOCK Reach through the front door of the Grandfather Clock and place your hand on the side of the pendulum disk. Move the pendulum to the far left of center and release. Let the Grandfather Clock operate a few minutes until the pendulum settles into an even swinging motion. (See figure 7). If your Grandfather Clock gains or looses time after twenty-four (24) hours, see General Information Section to regulate the timekeeping of your Grandfather Clock. After the Grandfather Clock has run for at least twenty-four (24) hours, remove the styrofoam blocks by lifting the blocks straight up until they clear the cable pulley. Then gently push them back, through the cables. |
______________________________________________________________
General Information
8. PRODUCT INFORMATION LABELThe product information label identifies the Grandfather Clock model number and serial number. The Grandfather Clock model number and serial number are essential for obtaining parts or service. The product information label is located in several locations: outside the shipping carton, back of door, back of the Grandfather Clock, top of the Grandfather Clock, inside the top back corner of the Grandfather Clock, or inside the Grandfather Clock above the back of the dial. Refer to this label when contacting your dealer or Howard Miller. For easy reference in the future, take a moment to record these numbers in the space provided in the Service Information Section (page 12.) Attach your sales receipt to this manual for future reference. ______________________________________________________________ 9.MOVING YOUR GRANDFATHER CLOCK Care should be taken whenever you move your Grandfather Clock to insure that all accessory parts such as the pendulum and weights are removed and packed properly to prevent damage. NEVER wind a cable drive movement without weights installed. ______________________________________________________________ 10. HOW TO REMOVE/INSTALL THE TOP SIDE PANELS FROM THE GRANDFATHER CLOCK Your Grandfather Clock may have wood or glass top side panels. When removed, you have access to the Grandfather Clock movement and chime area. The panels may be held in place during shipment by tape or a plastic clip. In order to remove the panel, reach in through the front door and turn the plastic clip or remove the tape. Then follow these steps: 1. Grasp the wood slats or knob with the tips of your fingers. Be careful not to push on the grill cloth or glass as you might separate it from the wood top side panel. 2. Lift the top side panel up. It rests in a groove on the bottom edge. 3. Push the bottom edge of the top side panel toward the center of the case while at the same time, pull the top edge down and out of the groove in the top of the opening. 4. Tilt the top edge of the top side panel toward the case center. 5. Remove the top side panel from frame opening, bottom end first. When installing wooden or glass top side panels reverse steps 1 thru 5. |
______________________________________________________________
11. RAISING WEIGHTS The weights must be raised every seven (7) days or the Grandfather Clock will stop. Cables with pulleys: Weights that are suspended by cables with pulleys should be raised by using the crank provided. DO NOT lift the weights by hand while cranking. Insert the crank into the crank holes located in the dial face (See figure 15), and turn the crank counter Clockwise. This will raise the weights. You cannot overwind the Grandfather Clock and the weights need to be near the top to run the Grandfather Clock for 7 days. Be sure to remove the crank before shutting the door. |
______________________________________________________________
12. REGULATING TIMEKEEPING Changing the speed of time keeping is accomplished by moving the pendulum disk up or down. The pendulum disk is moved up or down by turning the adjustment nut. To slow the Grandfather Clock down, move the pendulum disk down by turning the adjustment nut to the left. To speed the Grandfather Clock up, move the pendulum disk up by turning the adjustment nut to the right. (See figure 17). Day One 1. Select a time of day that will allow you to check your Grandfather Clock at the same time for at least six days. 2. Record time selected. 3. Check correct time. 4. Re-set the minute hand to the exact, correct time. Day Two, Three, Four, Five, Six (If Necessary) 1. Check correct time. 2. Compare time shown on your Grandfather Clock with correct time. Is your Grandfather Clock fast or slow? 3. Turn the adjustment nut on the pendulum one complete revolution for each half minute fast or slow per day. (24 hours). 4. Check correct time. 5. Re-set the minute hand to exact, correct time. |
______________________________________________________________
13.Automatic Night-Time Silencing Option Many Grandfather Clocks will offer a night time shutoff option. There are 3 options on this lever. 1) 'Night On' - This will keep the chime striking 24 hours 2) 'Night Off' - This position will turn off the chiming between 10:15PM and 7:00AM 3) 'Strike' - This position will allow the movement to strike the hour without the Westminster melody if the other Westminster melody lever is turned to Silent. ______________________________________________________________ |
14. CHIME SELECTION Selecting the chime melody is accomplished by a selection lever on the Grandfather Clock dial. Some models play only the Westminster chime, while others give you a selection of three melodies. Selection of the chime sequencing feature or one of the three chime melodies is done with the selector lever. If the dial states ?Chime-Silent,? your Grandfather Clock has only the Westminster chime. If your Grandfather Clock has a triple chime movement, the chime lever identifies the melody choices. All floor Grandfather Clock movements have the Big Ben hour gong which will count the hour, on the hour. DO NOT attempt to move the chime selection lever while the Grandfather Clock is chiming. Doing so could damage the chime mechanism. See figure 18 for when it is safe to move the chime selection lever without damaging the movement. MOVE CHIME SELECTION LEVER ONLY WHEN MINUTE HAND IS IN SAFE TIME AREA |
______________________________________________________________
TROUBLE SHOOTING
15. DIFFICULTY TURNING THE MOON DIAL As you face the Grandfather Clock, remove the top side panel, open the side door, or remove the back access panel. Look at the back side of the dial and locate the click spring. Put your finger at the tip of the click spring. Pull the click spring approximately 1/2? back away from the saw tooth moon dial and then release. (See figure 19). The click spring and dial should snap into proper alignment. If the click spring is in its proper location and you still feel resistance when trying to advance the moon dial DO NOT FORCE IT. If the moon dial still cannot be easily advanced, this indicates that the gears that automatically advance the moon dial are engaged. To correct this rotate the minute hand backwards three hours as describe in Step 5 of the setup operation. |
______________________________________________________________
16. GRANDFATHER CLOCK DOES NOT CHIME AT PROPER TIME If the Grandfather Clock chimes more than one minute before or after the proper time, the minute hand should be removed and adjusted. CAUTION: When performing this operation be careful not to scratch the hand nut, hand or dial. 1. When the Grandfather Clock starts to chime, stop the pendulum and record the time. 2. Using pliers, carefully remove the small nut that holds the minute hand in place by turning the nut counter Clockwise while at the same time hold the minute hand with your fingers near the small nut. 3. Remove the hand from the hand shaft by grasping it with your fingers at the point where it attaches to the shaft. Pull the hand straight off. This hand is not screwed on and should come off easily. The minute hand has a small raised area on the back side directly around the shaft hole, this is the hand bushing. Using pliers, grip the bushing firmly by its sides so that it cannot slip in the pliers. With your other hand, turn the Grandfather Clock hand forward or backward the distance necessary to chime at the correct time. (See figure 20). 4. Re-attach the hand to the shaft and turn the hand nut finger tight. Make sure the hand points to the correct location that you recorded in Step 1 plus any corrections you made in step 3. If the hand does not point to the correct mark, repeat steps 2 and 3. 5. Snug up the hand nut with the pliers. Do not over tighten. 6. Start pendulum. 7. Re-set the time by moving ONLY THE MINUTE HAND counter Clockwise (backwards) as described in Step 5 of the set-up operation. EXAMPLE: Grandfather Clock chimes at 1:10 but should chime at 1:15. Step 1: When Grandfather Clock chimes at 1:10 stop the pendulum and record the time of 1:10. Step 2: Carefully remove the small nut. Step 3: Remove the minute hand. Grip the bushing by its sides and turn the hand forward 5 minutes. Step 4: Reattach the hand so it points to 1:15. Attach the hand nut finger tight. Step:5 Snug up the hand nut. Step 6: Start pendulum. Step 7: Reset Grandfather Clock to current time. |
______________________________________________________________
17. GRANDFATHER CLOCK DOES NOT STRIKE THE CORRECT HOUR If after several hours of operation your Grandfather Clock does not strike the correct hour, grasp the HOUR HAND ONLY and move it forward or backward to line up with the correct hour on the dial indicated by the number of times the hour strikes. Rotating this hand independently will not damage the Grandfather Clock. If the minute hand needs to be reset (to correct time), move the minute hand counter Clockwise (backwards) as described in Step 5: Setting Time. |
______________________________________________________________
18. GRANDFATHER CLOCK WILL NOT CHIME OR STRIKE 1. Make sure that the selection lever is not in the ?silent? position or halfway between two chime melody positions? 2. Make sure that all the packing material is removed from the movement area. 3. Make sure that the weights are hanging in the correct location Check the label on the bottom of each weight to ensure proper location. 4. For models with nighttime silencing, make sure that the Grandfather Clock is not in the nighttime silence mode. (Reference: See AUTOMATIC NIGHTTIME SHUT OFF OPTION in General Information Section). 5. Check hammer adjustment and correct chime tone as necessary. 6. Move the chime selection lever to a different melody or to ?silent?. 7. It is possible that the styrofoam blocks located above the cable pulleys are binding the cable. Carefully remove the styrofoam blocks by lifting the blocks straight up until they clear the cable pulley. Then gently push them back through the cables. Do not use tools to remove the blocks. Do not permit the cable to overlap on the drum. |
______________________________________________________________
19. CHIMES HAVE THE INCORRECT TONE DO NOT ADJUST CHIME HAMMERS, unless the chime tone is incorrect. Chime tone may be affected by the hammers resting on the chime rods or striking the rods off center. Although the hammers were set at the factory, it is possible for them to get out of adjustment. For most Grandfather Clocks, it will not be necessary to adjust chime hammers. CHIME ROD hammer arms are made of brass and can be safely bent. If necessary, adjust hammers so that they do not interfere with each other while moving or striking the chime rods. This is accomplished by bending the hammer arms slightly in the middle so that each hammer rests approximately 1/8? from each rod. (See figure 22). DO NOT bend the chime rods. Chime volume cannot be adjusted on a chime rod movement. The hammers should rest approximately 1/8' from the rods. When the hammers retract during a striking sequence, they should draw back about one hammer length. If a hammer 'double strikes' when it hits the rod it will give a muffled sound and needs to be formed back further from the rod. If the sound isn't lound enough, it needs to be closer. It takes practice to get it sounding right. ______________________________________________________________ 20. WEIGHTS DO NOT DROP AT THE SAME LEVEL When the automatic nighttime shutoff feature is selected, and on some models the ?silent? feature, the center weight will drop at a faster rate than the other weights. ______________________________________________________________ This information is only for the clocks that we offer at this time and may or may not be appropriate for other brands and older clocks. We cannot be responsible for any user adjustments performed on any clocks outside of the clocks that we have sold. We also cannot properly answer questions on older clocks, clocks that we have not sold or brands we do not sell. ______________________________________________________________ |
Grandfather Clocks 123 - © - All Rights Reserved. |
Don't See Your Clock Movement Listed?
Send me a picture of your clock movement. I will either send you a quote or direct you to the correct rebuild service for your clock movement.
Urgos Clock Movement Parts
Any bushings the clock movement needs.
This clock movement will receive at least 24+ bushings.
Cleaning and oiling the clock movement.
Three year warranty on bushings and labor.
Return shipping is included in the price.
Other Possible Repair Issues Not Included In The Price:
Damaged Or Broken Parts Such As; Teeth, Pinions, Pivots, Cables, etc. Excessively Rusty Or Tarnished Parts. Any Parts That Are Missing.
When I Receive Your Clock Movement:
I will inspect it for any extra repair issues such as those listed above. If any of these issues are found, I will contact you with an explanation and a price adjustment before proceeding with the rebuild. If you find that the price adjustment is not agreeable, I will return your clock movement to you and issue you a refund, minus the cost of return shipping.
My Average Turn Around Time Is Around 90 Days Or So From The Day I Receive Your Clock Movement.
Packing Instructions:
This Clock Movement Has Special Packing Instructions That Must Be Discussed Over The Phone.
Please contact me if you require assistance removing or reinstalling your clock movement from its case. We can arrange a time to discuss it over the phone.
Please be sure to include the hands, the cables & pulleys, the suspension spring, the pendulum leader, and the seat board with the hammer assembly with the movement. Do not send the pendulum or weights.
How The Clock Movement Wears:
This Urgos Clock Movement is made up of 2 brass plates with 23 gears in-between them. Each gear shaft has two pivots, one at each end, that ride in a hole in each of the plates. As the movement runs, the pressure from the spring turns the first gear in one direction, that gear turns the next gear in the opposite direction, and so on. Whichever direction the pressure presses the gear to run, the pivot holes in the plates will wear in that direction. The more the holes wear, the more the gears drag as they move out of alignment, and the more power the movement needs to continue running. Eventually the movement wears to the point that the spring cannot supply enough power to run the clock. At this point the movement will need to be rebuilt.
How The Clock Movement Is Rebuilt:
First the clock movement is completely disassembled and ran through the cleaner. Next, all the worn pivot holes are realigned and then drilled out to the proper size of the bushing it is to receive. The bushings are then pressed into the holes and touched up with a bushing reamer, as needed, to provide adequate clearance for the pivots. (I use only high quality KWM bronze bushings) The movement is then oiled, reassembled, and thoroughly tested.