The rifle has matching serial numbers, except for the barrel band, trigger guard plate and the buttstock sling swivel (the matching serial numbers are stamped on the receiver, barrel, buttplate, bolt body, bolt head, bolt cocking piece, safety lever, front sight and rear sight). All the parts of the bolt display matching serial numbers. Aug 07, 2010 The R in the serial number indicates you have a Romanian Vz-24. The H signifies a specific manufacturing period, but I don't have a chart, or know of one. You don't say if it's in military condition, or has been sporterized, as happened with many Mauser's. If sporterized it was not unusual for markings to be altered. Czech Vz24 Mauser.In good looking condition and likely refurbished over the years of service. Serial numbers no longer match. Czech markers marking on the receiver from the Brno Arsenals.Meal finish is blued and thinning on the barrel with wear most wear on the band and sharp edges. The stock carries the same serial number as the action /Rifle bore and rifling Very good /Fore sight protector fitted /Gunsmith checked / suit service rifle competitor./. Rebarreled from 8x57 to 308 to duplicate South American rifles for Military/Service Rifle Comp./The rifle was part of a huge buying spree by the Chinese Nationalist in the 1930's.International Arms dealers sold batches of. The M1922 rifles can be found with sights marked in western or the old Farsi type numbers used on the Persian Mausers. This relationship continued up through 1938. In addition to the rifles mentioned above ZB supplied several other Mauser designs for export. 1)The Model JC, a reduced weight Vz24 with slimmer barrel and stock.
Bolivia
Brush sets for autodesk sketchbook pro mac. The Czech VZ 1924 Pistol
by Ed Buffaloe
|
![See full list on worldwartwo.wikia.org See full list on worldwartwo.wikia.org](https://media.joesalter.com/ca/large/C982/C982-02.jpg)
Vz 24 Mauser Serial Numbers
Ceska Zbrojovka (CZ) had to redesign the pistol for two reasons: 1) to adapt production to the existing machine tools at CZ, which would serve to speed production and reduce costs and, 2) to meet the demands of the Czech Armament Commission to make the gun reliable enough to serve as a military weapon. The most important changes were the addition of a disconnector and a magazine safety, which had been notably lacking on the vz.22. The manual safety lever, safety release, slide retention pin, and side plate of the new design were stamped instead of milled. The cradle that the helical lug of the barrel turns on was redesigned to be symmetrical (i.e., reversable), and a stop lug was added to the barrel. The trigger design was simplified, the barrel and slide were lengthened slightly, a set screw was added to the side plate, the front sight profile was changed, and the rear of the ejection port was rounded instead of straight.
Two-hundred pre-production pistols were delivered to the Czech Armament Commission for testing in May of 1925. The Commission approved the design by August of 1925, and the redesigned gun was designated the vz.24.
The first government order for 20,000 vz.24 pistols was completed in June of 1926. According to Berger, by the end of 1929 a full 100,000 pistols had been delivered to fulfill additional government contracts, though Ezell states that they were not delivered until 1931. An additional 1400 were made in 1935, and 70,000 were made between 1936 and 1938 to fulfill later government contracts. CZ’s intention had been to sell the gun commercially, but very few sales were ever made outside of Czechoslovakia. Approximately 1700 were sold to Poland, and another few hundred to Lithuania.
A nine-shot extended grip-frame version of the vz.24 was manufactured between 1929 and 1931, some of which were fitted with a combination shoulder-stock and holster. The nine-shot vz 24 pistols were given a separate serial number range from 1 to approximately 3100. A small number of regular 8-shot vz.24 pistols in the serial number range from 95,000 to 115,000 were also fitted with shoulder stocks. These guns were likewise made between 1929 and 1931 and are marked with an “A” in an oak leaf on the trigger guard.
|
A small number of vz.24 pistols were manufactured during the German occupation in World War II. These guns do not have serial numbers or any markings other than CESKA ZBROJOVKA A.S V PRAZE on top of the slide, though they do have a Waffenamt proof mark on the barrel.
When a cartridge is fired the locked barrel and slide recoil together for only about one millimeter before the helical lug, moving in the cradle, begins to rotate the barrel counterclockwise and unlock the breech. Total movement of the barrel during recoil is approximately 9 millimeters. Barrel movement is halted by the stop lug abutting the front of the cradle. Once the locking lugs disengage from the locking cuts, the slide is free to recoil on its own. As the slide recoils, the shell is extracted and ejected, and a new cartridge is fed into the chamber in the usual manner.
The trigger and lockwork of the vz.24 are very similar to the 1914 Mauser pocket pistol, but with a hammer in place of a striker. As on the Mauser, a sideplate allows access to the lockwork, the manual safety blocks the sear, and there is no backstrap on the grip frame. The mainspring and magazine release spring are screwed directly to the back of the grip frame and are covered by the wraparound grip. Most early grips are of wood, some checkered, some not; late production grips appear to be checkered plastic with the CZ monogram.
Field Stripping:
- With magazine empty, retract the slide. The slide will lock open, relieving tension on the pin that retains it.
- On the right side, press in on the protruding end of the retaining pin. Slide the left side locking tab down, out of the frame, and pull the pin out from the left side.
- Hold the slide back with one hand and remove the magazine with the other.
- Ease the slide forward off the frame.
- Turn the barrel bushing approximately 30° and remove it from the slide.
- Remove the barrel through the front of the slide.
There is no need to remove the sideplate for normal cleaning.
R.K. Wilson says of the vz.24 that it is “..well thought out in every particular. It is extremely well made of first class material..,” and it “..groups very well and is quite easy to shoot with.” His only criticism of the vz.24 is that its grip is too square to the frame and therefore the gun does not point naturally--but he says it isn’t as bad as some guns, such as the Steyr-Hahn 9mm.
|
- Listed In: Antique Firearms
- Flag
- Report illegal firearms activity to 1-800-ATF-GUNS or your local police department.
Share:
This Czech VZ 24 is a CAI import gun. Chambered in the 8mm Mauser round and has had a Sniper scope Mount added to it at some point. (NO scope base or scope available). I do not think this was originally built as a Sniper as it has a straight bolt handle, but then again the bolt serial number does not match the receiver. Rifle appears to be all original finish with a greying patina. Sale includes a Paul Weyersberg & co. Solingen marked bayonet that has bakelite handle.
Store hours Wednesday-Friday 1-6 Saturday 10-2. Telephone 1-660-547-3068. We are located on Hwy65 on the north end of Lincoln, Missouri. All items we sell are available for shipping at the buyers expense. Firearm shipping will require FFL. Credit card purchases will be charged an additional 3% of total to cover our costs for the service.
Premium Vendor Details Ozark ArmoryArmslist Store- 660-547-3068
- Lincoln, Missouri, United States
- Yes
- CATEGORYAntique Firearms
SPONSORED
SPONSORED
Listed On: Saturday, September 5, 2020post id: 9727248